![]() Hell, even if I want to make some scratch tracks while writing I don't hook up the Axe's USB at all and just arm my track/s using S/PDIF inputs and you're good to go. Seems a bit complicated, but once everything's set and running it's a bliss (I have an AX8 too, and before getting the III, reamping was much more complicated as I had to use a reamp box. I use 2 cables for S/PDIF in and out so the Axe FX is always 'slave' for the Scarlett and avoid having to switch the clock from internal to external on the Focusrite Control app every time I want to use the III. One important thing is that I hook up the Axe FX to the Scarlett via S/PDIF so i'm monitoring with "ultra-low" latency as the Scarlett allows for hardware monitoring. Basically, I make an "Aggregate Device" so I can use both units at the same time, this way I do all my monitoring with the Scarlett and only select Axe FX's USB as my I/O when tracking/reamping. I'm a Mac/Logic Pro X user, so take this into account. I track AND reamp via USB while monitoring using a Focusrite Scarlett 18i20 Gen 3. This is the setup I've used for years and it's super flexible.įor the AxeFX specifically, I don't know what benefit a dedicated reamp box would give you, but if you have actual hardware amps you want to reamp with then it could be beneficial for sure. Then when you want to reamp, you change the SPDIF Out to be one of the DAW playback outputs, and set the DI track to that output. La palabra Reamp ha aparecido cada vez con más frecuencia a medida que los pedales y amplificadores que habitualmente publicamos en estas páginas se han ido modernizando. As an added bonus, you can record both the mono DI signal and a stereo AxeFX signal at the same time. Then you can just record both Input 2 and whatever input the SPDIF In from the AxeFX is (I think it's like 9-10 or something like that). The basic gist is you plug the guitar into the Pro 40 (I used the front panel Input 2), then you route that Input directly into the SPDIF output, which feeds into the AxeFX. It also lets you reamp in a pinch entirely in software, without having to mess with any cables. This is going to give you the most flexibility in terms of tracking both DI and AxeFX sounds, and you can use your Pro 40 as the primary interface and not lose any signal quality due to AD/DA conversion. I would suggest connecting the AxeFX to the Pro 40 with two RCA SPDIF cables. I'm currently using the Scarlett 18i20 3rd gen, but my previous interface was the Saffire Pro 40. Which brings me to my next question: Are you guys doing any reamping with the axe fx iii with a box like a radial x-amp or jcr, little labs redeye, etc? I think I'm leaning towards a dedicated reamp box any way since I have some amps I could utilize this method with, but I'd love to hear the pros and cons of each scenario and what you guys are using/doing. I kinda of don't want to have to unplug my monitors and swap this stuff back and forth, but I am assuming this is my only option if I want to reamp via usb with the axe fx iii, no? I'm using Pro Tools and I have a focusrite saffire pro 40 that I'm using for an interface and monitoring through. For you guys who are using it that way, how are you monitoring? Headphones? Speakers? Are you using it as an interface, or are there other options to achieve monitoring? I know this can be done via usb and using the axe fx iii as an interface. I had a question about reamping with the axe fx iii. See this article for an in-depth discussion of the caveats of that trick long story short, you either need a DI with a built-in pad or you need to build your own inline pad to get the level anywhere near what a guitar amp needs. I'm also looking at the Sowter 3575 and Edcor WSM and XSM 10K transformers.Hey, everyone! I hope everyone is well and safe! My understanding is that only a passive DI is suitable as a substitute for a reamp box. I'm looking at the Jensen JT-11P-1 that's mentioned in the schematics. Then I also have a transformer shootout going. I don't want to get crap pots but I don't have any idea what's good or bad. What kind of switches would I need if I want to make something like the GIMP which combines two schematics using only one transformer.ģ. ![]() Would you build something like this on a PCB or not?Ģ. ![]() So schematics wise I'm pretty ok but I have a few questions.ġ. I have the Jensen schematics listed on the previous page and also found this. I'm looking at building a guitar ReAmp box like this but the link to the GroupDIY thread where this was discussed is not working (and now this link is not working either).
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |